Hi. Window not closing properly?

Window adjustment. Window closes again
evenly in all corners.

25
From / window pane
20min
One window pane
0
Initial estimate
what we do

Closing pressure adjustment, hardware check, window position. Often it’s enough to make the window seal again without replacing the seal. From €30 per pane, ~30 min.

4 steps

Same process. Every window.

Diagnosis, removing the old seal, Q-Lon installation, check. One window pane takes about half an hour. The window stays in place, the glass unit is not removed.

01 · Diagnoos 01 We inspect the window condition, check the seal

We check where it’s drafting from

We inspect the entire window and tell you honestly whether a seal change will help.

02 · Vana eemaldus 02 We remove the old seal

We remove the old seal

The old hardened rubber seal comes out completely, the profile is cleaned.

03 · Q-Lon paigaldus 03 We install the Schlegel Q-Lon polyurethane seal

We install the Q-Lon seal

German Schlegel polyurethane seal is applied evenly along the entire frame.

04 · Valmis 04 Finished work, window closes evenly

The window is sealed

Closes evenly, draft is gone. You’ll feel the difference with the first close.

Before we sell

We don’t start with selling a seal.
We start with inspection.

The cause of a window problem isn’t always the seal. The first thing we do is inspect the entire window. If a seal change won’t help, we say it before the work, not after.

1

Seal condition

Whether the seal is hard, sagged, cracked or slipped out of its proper position.

2

Closing pressure

Whether the window closes evenly against the frame in all corners.

3

Hardware and lock

Whether the handle and lock pull the window fully shut or need adjustment.

4

Glass unit and frame

Whether the problem may be in the glass, frame or installation joint (not the seal).

5

Humidity and ventilation

Whether condensation and cold come actually from lack of ventilation.

6

Cold bridge

Whether cold comes from between the window or from the wall-window junction.

How the work goes

Neli sammu
you don’t need to know anything.

01

You describe the problem

One sentence is enough. Call, write or use the form.

02

We inspect the window

We come on site, check the cause. Tell you honestly what is wrong.

03

We seal the window

We replace the seal and adjust if needed. ~30 min per window pane.

04

We check the result

We check the closing is even. You feel the difference instantly.

Q-Lon polyurethane seal
Material

Schlegel Q-Lon.
Saksa polüuretaantihend, mis ei muuda kuju.

We use only Schlegel Q-Lon polyurethane seals. It is the German industry standard installed on European premium windows for over 50 years. Unlike ordinary EPDM rubber, Q-Lon does not change shape in the cold, does not harden, does not crumble. The seal we install today will work the same way 10 years from now.

  • MaterialPolyurethane (PU foam)
  • ManufacturerSchlegel · Germany
  • Lifetime10+ years without deformation
  • Withstands−40 °C to +90 °C
  • Pricefrom €25 / window pane
Google reviews

4.9 ⭐ 87 reviews

Real customers, real ratings. Good and bad, all there. View on Google Maps →

AknaOnu OÜ

4.9 (87)
Open · Closes 18:00
Tallinn, Harjumaa
+372 5832 0588
M
Mari L.
Local Guide · 12 reviews · 4 photos
2 weeks ago

Came on site the day after I called. Looked over the window, told me honestly what was needed, and did it in 30 minutes. Draft completely gone. Price was reasonable, no attempt to upsell anything. Recommend!

T
Toomas R.
5 reviews
1 month ago

Needed to replace seals on 6 windows in Maardu. Fast and proper work. Windows stayed in place, workers were polite, all debris taken away. Price was exactly what was quoted after the on-site inspection.

E
Eve K.
Local Guide · 28 reviews · 16 photos
3 weeks ago

I was sure the whole window needed replacing. But the AknaOnu master said: “It’s only the seal and closing pressure.” Did it without removing the window. Condensation dropped noticeably. Thank you!

Honest talk

When a seal change helps, and when not.

A seal isn’t a miracle cure. Below are honest limits: where it solves the problem and where something else is needed.

Often helps when

  • Window drafts or air leaks near the window
  • Seal is hard, cracked or sagging
  • Window closes unevenly
  • Cold comes specifically between the frame and the window
  • Noise comes through the seal gap
  • Window is over 10 years old

Alone won’t help when

  • Glass unit is broken or fogged
  • Room humidity is too high
  • Cold comes from the wall-window junction
  • Hardware is broken, can’t be adjusted
  • Window frame is deformed
  • Problem is in the cold bridge (wall itself)
The numbers speak

10 years, thousands of windows.

Not every job is in a photo. Not every client leaves a review. But the numbers remain.

2400+
windows repaired in total
In Tallinn, Harjumaa and across Estonia
80%
solved without a new window
Seal + adjustment = enough
20min
one window pane
Window stays in place, glass unit isn’t removed
24kuud
written warranty
On every job, on every seal
Frequently asked questions

What people ask before ordering

Will a seal change definitely help if there’s a draft from the window?

Often yes, especially if the window is over 10 years old and the seal hasn’t been changed before. But not always. We first check whether the cause is in the seal, closing or elsewhere. If a seal won’t help, we say so before the work, not after.

How much does it all cost?

From €25 per window pane. The final price depends on the window size, profile and quantity. After an on-site inspection we can give an exact price, and the inspection is free.

Does the window need to be removed?

No. The window stays in place, the glass unit isn’t taken out. Work is done on site, one window pane takes about half an hour.

Why Q-Lon specifically?

Q-Lon is Schlegel’s polyurethane seal, designed for the Northern European climate. Unlike standard rubber, it doesn’t harden in cold and works the same years later.

Does a seal change help with condensation?

Sometimes yes, sometimes no. Condensation forms when warm room air touches a cold surface. Poor sealing can worsen the problem, then a seal change helps. If the main cause is humidity, ventilation must be improved first.

How quickly can you come?

In Tallinn and Harjumaa usually within a few days. Describe the problem, we’ll tell you when we can come earliest.

Don’t know what the problem is?
No worries. Write a few sentences.

We’ll check and tell you whether a seal change, window adjustment or something else is needed.

📞 Helista Kirjelda probleemi